CD422 / CD432 / CD622


CD422 / CD432 / CD622 

  CD422 / CD432 / CD622


 

   - بدنه پلاستیکی و سیم بندی کامپکت
   - ولتاژ منبع تغذیه :  AC220V -20/+15% 47-63Hz
   - ولتاژ منبع تغذیه مدل CD622 :   AC380V -20/+15% 47~63Hz

 

Model parameter CD422-AA-000 CD432-AA-000 CD622-AA-000
Power Main supply voltage Single-phase AC220V -20/+15% 47~63Hz Single-phase or 3-phase AC220V -20/+15% 47~63Hz 3-phase AC380V -20/+15% 47~63H 
Control circuit voltage 18VDC~30VDC 1A
Current Rated current(RMS) 4A 10A 7A
Peak current(PEAK) 15A 27.5A 25A
Feedback signal 2500PPR (incremental encoder with 5V supply)
Brake chopper Use an external braking resistor according to application, mainly in occasion of quick stop.
Brake chopper threshold DC380V±5V DC680V±5V
Over-voltage alarming threshold DC400V±5V DC700V±5V
Under-voltage alarming threshold DC200V±5V DC400V±5V
Cooling method Natural air cooling Fan
Weight 1.2kg 2.4kg
Position
Mode
Max. frequency of input pulse Differential signal: 500KPPS, Open-collector signal: 200KPPS
Pulse command mode Pulse+direction, CCW+CW, A+B phase (5V-24V)
Command smoothing Low-pass filtering(Internal parameters)
Feedforward gain Internal parameters
Electronic gear ratio Setting range, Gear factor: -32768~32767, Gear divider: 1~32767, 1/50≤|Gear factor/Gear divider|≤50
Position loop sampling frequency 1KHz
Speed
Mode
Analog input voltage range -10 ~+10V(Resolution 12bit)
Input impedance 200K
Analog input sampling frequency 4KHz
Command source External analog command/internal command
Command smoothing Low-pass filtering(Internal parameters)
Input voltage dead-zone setting Internal parameters
Input voltage offset settiong Internal parameters
Speed limit Internal parameters
Torque limit Internal parameters / External analog command control
Speed loop sampling frequency 4KHz
Torque
Mode
Analog voltage input range -10 ~+10V (Resolution 12bit)
Input impedance 200K
Input sampling frequency 4KHz
Command source External analog command/internal command
Command smoothing Low-pass filtering(Internal parameters)
Speed limit Internal parameters /External analog command control
Input voltage dead-zone setting Internal parameters
Input voltage offset setting Internal parameters
Current sampling frequency 16KHz
Digital
Input
Input specification 7 digital inputs, with COMI terminal for PNP (high level valid 12.5-30V)or NPN (low level valid) connection.
Input function Define freely according to requirement, supporting following functions: Driver enable,driver fault reset,driver mode control, proportional control, positive limit, negetive limit, homing signal,reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain
Digital
Onput
Output specification 5 digital outputs,OUT1 - OUT4 current is 100mA, BR+/BR- (Brake control ourtput ) current is 500mA, can drive brake device directly
Output function Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, N signal, maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached
Protection functions Over-voltage protection,under-voltage protection,motor over-heat protection(I²T),short-circuit protection,drive over-heat protection,etc.
Communication interface RS232 (Connections with PC: 2-2, 3-3, 5-5)
Operation
Environment
Operating temperature 0 - 40℃
Storage temperature -10℃ - 70℃
Humidity(non-condensing) Below 90%RH
Protection class IP20
Installation environment Installed in a dust-free,dry and lockable environment(such as in a electrical cabinet)
Installation mode Vertical installation
Height No power limitation below 1000m
Atmospheric pressure 86kpa~106kpa

نام فایل نوع فایل فرمت تاریخ دریافت فایل
Russian Kinco CD/CD2 Series Servo Catalog کاتالوگ محصول zip 2013-11-01
Kinco Products Catalog کاتالوگ محصول zip 2012-08-03
CD/CD2 Servo Catalog کاتالوگ محصول zip 2012-06-25
3D model for Kinco SMH80 series motor 3D model rar 2012-02-06
ED Servo Catalog کاتالوگ محصول zip 2011-05-19

نام فایل نوع فایل فرمت تاریخ دریافت فایل

 

JoomShaper